Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Company in Ennis, TX
Gate repair in Ennis means working on equipment that has to survive Blackland Prairie clay. The soil here shrinks in dry summers and swells through wet winters, pushing posts out of line and throwing automatic operators out of adjustment faster than most homeowners expect. Whether you’re on an older lot near downtown or an acreage tract east of town, the job starts with understanding what the ground is doing under the gate. We answer the phone around the clock at (940) 412-7340, and every repair gets a written price before any work starts.
Why Ennis Homes Are Different
Ennis sits on some of the heaviest black clay in North Texas. That detail changes almost every gate job here. Posts set without deep, bell-bottom concrete footings will heave two to three inches after a wet winter, and that movement pulls hinge leaves out of alignment, binds latch bars, and torques actuator arms until the operator strains or burns out. We see it most on the acreage roads south and east of town, where a lot of the original Czech-heritage farmsteads have been converted to gentleman ranches and ranchettes. Those properties typically have a road-entry gate that’s either an older agricultural pipe-and-panel setup or a newer automatic operator that was installed without accounting for soil movement.
The climate adds a second layer. North Texas ice storms knock out power for days at a time, and most rural operators here don’t have battery or solar backup wired in. When power returns, we get a wave of calls for boards that surged, motors that locked, and keypads that lost their programming. Closer to downtown, the early and mid-20th century homes have tighter setbacks and older gate hardware, but the same clay is still moving under every post. In Ennis, you don’t just adjust an operator. You check the posts first, or you’ll be back out there in six months.
Our Main Ennis Services
Most Ennis calls come down to two things: a gate that won’t open or close reliably, and a gate that needs to be designed and set for this soil from day one. Here’s what each one involves locally.
Gate Repair in Ennis
Most repair calls in Ennis start with a gate that drags, binds, or won’t latch, and the root cause is usually the ground, not the hardware. We re-plumb posts, rebuild hinge mounts, replace bent or seized wheels on cantilever and V-track systems, and re-time the operator once the gate swings or slides freely again. If your gate hangs on a post set in black clay, we quote the post reset before touching any operator setting, because adjusting the operator around a moving post just guarantees another call-back. Gate Repair in Ennis covers the full scope, from sagging field gates to ornamental driveway systems near downtown.
Gate Installation in Ennis
A new gate on Blackland Prairie soil has to be built for movement, or it won’t stay square. We set posts in deep concrete footings with the base belled wider than the shaft so the clay can heave without lifting the post, then build the gate around that foundation. Ennis properties range from tight in-town lots to wide ranch entries, so there’s no stock answer. Working cattle and horse operations east of town often need heavy agricultural pipe gates, while ranchettes closer in want ornamental steel with an automatic opener. Gate Installation in Ennis walks through both.
Electric Gate Repair in Ennis
Electric gate repair here usually means a swing-arm actuator that’s been fighting a post the clay moved, or a control board that took a hit when the power flickered during a storm. We work on Viking, Ghost Controls, DoorKing, and Elite systems among the major brands, and we diagnose the full circuit: power supply, wiring run, safety edges, and operator settings. The important part is that we check the mechanical alignment before we condemn the electronics, because in Ennis the electronics are rarely the first thing that failed. Electric Gate Repair in Ennis has the details.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service in Ennis
We service residential and agricultural operators from Viking, Ghost Controls, DoorKing, and Elite, plus the other major brands we carry parts for. Our techs arrive already familiar with the machine on your property, which shortens diagnosis and keeps the job moving. See our brands for the full list.
Pricing for Gate Company in Ennis, TX
| Service | Typical range in Ennis |
|---|---|
| Service call and diagnosis | $59-$99 |
| Gate won’t open or close (basic repair) | $150-$350 |
| Swing gate operator replacement | $650-$1,200 |
| Slide gate operator replacement | $850-$1,500 |
| Post re-plumb and reset | $250-$600 |
| Hinge and latch rebuild | $125-$325 |
| Battery backup installation | $250-$500 |
| Solar backup installation | $450-$800 |
| Full gate installation (residential) | $1,500-$4,000 |
The biggest price driver on an Ennis job is the soil. A post that’s heaved out of line adds a re-plumb line item to what looked like a simple operator swap, and it’s work you don’t want to skip. Whatever the final scope, you’ll see the full price in writing before we turn a bolt, so the invoice never surprises you.
Neighborhoods We Serve in Ennis
We run calls across the whole Ennis area, from the older streets near historic downtown out to the acreage tracts and ranchettes south and east of town. Dispatch is coordinated from the brand’s Dallas-Fort Worth office, and crews are routed into Ennis daily, so most repairs happen same day or next morning.
- Downtown Ennis and the surrounding historic neighborhoods
- Country Club Road corridor
- Ennis Lake and Bardwell Lake areas
- Acreage tracts east of I-45 toward the Ellis County line
- Ranchettes south of town along Farm-to-Market roads
Service Area – Cities Near Ennis
We work throughout Ellis County and the neighboring communities, so if your property sits between towns or you have family with a gate a few miles over, we can usually help. In addition to Ennis, we serve Waxahachie, TX, Red Oak, TX, Wilmer, TX, and Lancaster, TX, with the same written-price and written-guarantee standard on every job.
Serving Ennis, TX - Our Local Coverage Area
We’re based in the Ennis area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Company in Ennis
Most Ennis repair calls are reached same day or next morning, because we route local crews daily from our North Texas dispatch. If you call first thing, we can usually set an arrival window the same day. Call (940) 412-7340 and we’ll give you a real window, not a four-hour range.
Most gate repairs and operator replacements don’t require a permit, but new installations with electrical runs sometimes do, depending on the scope and location. We check the current Ennis and Ellis County requirements on your project before quoting, so the paperwork is handled before the dig starts.
Yes. Ennis has a real mix of working horse and cattle properties and in-town residential lots, so our crews move between heavy agricultural pipe gates and ornamental driveway systems every week. The same Kingswell Guarantee applies to both: a written price, a real arrival window, a clean job site, and a 365-day written repair guarantee.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Ennis Customers Say
"Our driveway gate stopped halfway and wouldn't close, which is a problem when it's the only thing between the street and the yard. They came out same day, replaced the motor, and it's smooth again."
- Leonard Pace"Gate wouldn't respond to the remote or the keypad. Turned out to be the control board. They had the part and swapped it the same visit. Quoted it first, no surprises."
- Everett Shaw"Electric gate kept doing its own thing, opening at random. The tech found a shorted sensor and a worn board, fixed both, and showed me the old parts. Price was what he quoted on the phone."
- Cassandra Pike