Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Company in Kirby, TX
Kirby is a small, fully incorporated industrial enclave completely surrounded by San Antonio, and gate work here follows a different rhythm than in neighboring cities. Roughly 2 square miles pack warehouses, trucking yards, and light-manufacturing facilities along the IH-10 and Loop 410 corridors, which means our Kirby calls skew toward heavy-duty commercial sliding and swing gates on industrial lots. The residential pockets are mostly 1950s through 1970s tract homes where original tubular steel and chain-link swing gates soldier on with decades of surface rust. If your gate drags, binds, or won’t close, call (940) 412-7340 for a written price before any work starts.
Why Kirby Homes Are Different
Kirby sits on highly expansive Vertisol black-clay soils that swell when wet and crack deeply during drought. Those boom-and-bust rainfall cycles make gate posts heave and tilt seasonally, so hinge misalignment and post-anchor failure are among the most common repeat service calls in the area. A gate that swung cleanly in March can bind against the latch post by August, not because anyone did anything wrong, but because the ground beneath both posts moved in different directions.
The residential gates are mostly aging mild steel, and the hard Edwards Aquifer water combined with humidity spikes after heavy San Antonio rains puts a mean coat of surface rust on everything. Many of Kirby’s original tubular steel gates have never been removed, sandblasted, and repainted, so the steel is thinner than it looks, especially at the bottom rail and hinge plates. On older industrial parcels, driveways have been repaved multiple times over the years without raising the gate infrastructure, so bottom-drag on sliding gates is a recurring complaint our technicians learn to diagnose on nearly every commercial call in Kirby.
Our Main Kirby Services
Most Kirby calls fall into two broad groups, with a third that covers the automated side of the trade. Here is what each involves here.
Gate Repair in Kirby
Most residential gate repair in Kirby starts with a leaning post or a hinge assembly that has worn loose against the stress of shifting black-clay soil. We pull the post, reset it with a proper anchor, and realign the gate to swing without drag. On commercial lots along IH-10 and Loop 410, the work is often heavier: bottom guide rollers worn flat, bent sliding-gate track, or a panel that drags on asphalt repaved above the rail. Each job gets a written diagnosis and a written price before a single bolt is turned. Gate Repair in Kirby covers the full breakdown.
Gate Installation in Kirby
New installations in Kirby mean confronting the soil before anything gets set in concrete. We size posts and anchors for Vertisol clay, not for the sandy loam you’d find further north, because a post set too shallow will be leaning within two rainy seasons. For commercial parcels, we measure the load capacity of the ground and match it to the gate weight and panel length. Whether it is a residential swing gate or an industrial sliding gate, the written quote includes concrete work, hinge and track hardware, and the full job scope. Gate Installation in Kirby walks through the process.
Electric Gate Repair in Kirby
When an electric gate in Kirby stops responding, the first thing a technician should check is whether the operator is fighting a gate that no longer swings true. Expansive soil shifts posts, which binds the hinges, which strains the actuator, which eventually fries the control board or strips the gearbox. We service nine major gate-operator brands and carry parts for the systems most common in this area. Same-day electric gate calls are available when the gate is stuck open or stuck closed. Electric Gate Repair in Kirby has the details.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service in Kirby
We carry parts and service experience across Linear, Viking, Ghost Controls, and DoorKing operators, among others. Our brands page lists the full lineup. In Kirby, the heavy commercial operators on trucking-yard gates tend to be Viking and DoorKing, so those parts stay stocked locally for faster turnaround on industrial calls.
Pricing for Gate Company in Kirby, TX
| Service | Typical range in Kirby |
|---|---|
| Gate repair service call | $59-$99 |
| Swing gate hinge replacement (pair) | $180-$420 |
| Swing gate actuator swap (operator arm) | $550-$1,100 |
| Sliding gate track and wheel replacement | $480-$1,300 |
| Control board replacement | $350-$850 |
| Gate post reset and concrete anchor | $250-$650 |
| Full commercial slide gate service (tune-up) | $275-$550 |
| Electric gate troubleshooting and diagnostic | $89-$159 |
What pushes a Kirby price toward the top of the range is usually what is underneath the gate rather than the gate itself: post anchors pulled loose by shifting clay, bottom rails that need cutting and re-welding after years of drag, or track that has to be re-bedded above the finished asphalt grade. The price we quote before starting is the price you pay, in writing, every time.
Neighborhoods We Serve in Kirby
We cover the full city limits of Kirby and the immediate industrial corridors. Most Kirby jobs get service within 24 to 48 hours for scheduled repair, and emergency gate-outs are prioritized when a gate is stuck open across a commercial driveway or a residential entrance is left unsecured.
- Old Kirby residential district
- IH-10 industrial corridor
- Loop 410 commercial belt
- Kirby warehouse district
- Residential pockets along Graytown Road
Service Area – Cities Near Kirby
Kirby is our home base for Bexar County work, but the service area stretches well beyond it. Homeowners and facility managers in San Antonio, FL call us for the same written-price standard. We also take residential and commercial gate jobs in Houston, TX, Dallas, TX, and Fort Worth, TX.
Serving Kirby, TX - Our Local Coverage Area
We’re based in the Kirby area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Company in Kirby
Most scheduled Kirby repairs happen within 24 to 48 hours. If a gate is stuck open on a commercial lot or a residential entrance is left unsecured, we treat it as an emergency and dispatch the first available technician. Call (940) 412-7340 to schedule a time window that works.
For residential gate repair, generally no. For a new commercial installation or any work that involves new electrical runs, Kirby may require permits depending on the scope and location. We handle the paperwork and confirm requirements before scheduling the work. Call (940) 412-7340 and we will check for your specific property.
Yes. Every repair, residential or commercial, carries a written guarantee stamped on the invoice. If the repair fails within 365 days, we return and correct it at no charge under the 365-Day Done Right Promise. That is the same standard across every Kingswell company, including each independently owned location.
Yes. Commercial sliding and swing gates along IH-10 and Loop 410 are a major part of our Kirby work. We service nine gate-operator brands, stock parts for the heavy operators common on trucking yards, and quote every commercial job in writing before work begins. Call (940) 412-7340 for a free estimate.
If your gate is dragging, leaning, or stuck in Kirby, call Portcullis Gate Repair at (940) 412-7340. We will give you a real price range on the phone and a written price before any work starts. A live person answers, day or night.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Kirby Customers Say
"The opener gave out and we were manually pushing the gate for a week. Portcullis got us in quick, swapped the opener, and set up the remotes for both our cars. Great to have it working again."
- Priscilla Nava"Our driveway gate stopped halfway and wouldn't close, which is a problem when it's the only thing between the street and the yard. They came out same day, replaced the motor, and it's smooth again."
- Leonard Pace"Gate wouldn't respond to the remote or the keypad. Turned out to be the control board. They had the part and swapped it the same visit. Quoted it first, no surprises."
- Everett Shaw