Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across Angleton
Gate repair in Angleton usually runs between $140 and $600 depending on what failed, and most jobs are done in a single visit. We’re the local Gate Repair team that shows up in a marked truck, writes the price down before turning a single bolt, and stands behind the work for a full year. If your gate is sagging, stuck, or dead after the last storm, call us at (940) 412-7340 and a live person picks up, day or night.
We know this stretch of Brazoria County. The flood-prone bottomlands, the clay that heaves under your post footings, the salt air working on your hinges. Angleton gates don’t fail like Dallas gates fail, and our crews service Angleton properties with that specific knowledge on every call.
Why Portcullis Gate Repair Is Angleton’s Preferred Gate Repair Company
We’ve been a Kingswell company since 2008, and every independently owned location, ours included, carries the same four guarantees: a written price before any work starts, a real arrival window, a clean job site, and a written guarantee on the repair. Around Angleton, homeowners tell us the same thing: another company either never showed, changed the number at the door, or went silent when the fix failed six weeks later. That’s why they call Angleton Electric Gate Repair instead. We don’t operate that way. Our 365-Day Done Right Promise is stamped on every invoice. If the repair fails inside that year, we come back and correct it at no charge.
Dean Prescott leads our team, and he’s built the Angleton route around one principle: answer the phone, commit to a window, and put everything in writing. Our technicians are background-checked and uniformed, so you know exactly who’s walking up the driveway. We answer calls 24 hours a day, seven days a week, including holidays. Not a voicemail tree. A person.
Metal Gate Repair in Angleton
Metal gate repair in Angleton is the most common call we run, and it’s not close. The salt-laden Gulf air, the summer humidity, and the clay soils all work against steel and iron. Weld joints crack at stress points. Tube steel rusts from the inside out, especially on untreated ranch frames. Hinges seize. Posts lean as the soil swells after a good rain at the head of Oyster Creek or out toward the county seat’s east side.
Hinge, Post & Realignment Work
When a metal gate drags the ground on the latch side, the post has usually heaved or settled in the expansive clay. We cut the post free, reset the footing at the right depth, re-plumb it, and re-tension the hardware so the gate swings or slides true. Most hinge and post repairs in Angleton run $180 to $420 parts and labor, depending on gate weight and how far out of plumb the post has moved.
Weld & Rust Repair
Rust on an Angleton metal gate isn’t cosmetic. We see corrosion eating through the bottom rail of ranch gates and driveway swing gates within a few years when they’re exposed to the brackish air that rides in with Gulf storms. Weld and rust repair typically runs $160 to $400. We cut out the compromised section, weld in a new piece, and treat the surrounding steel so the repair doesn’t fail at the next seam.
Wood Gate Repair in Angleton
Wood gate repair in Angleton follows a different pattern than metal work. The mid-century homes near the courthouse square and the ranch-style properties on larger parcels both use wood, but the failures differ. Humidity swells the boards. Clay heaves the posts. And on wide acreage gates, the frame starts sagging until the latch no longer lines up.
Sag Correction & Frame Rebuild
A wood gate that drags or won’t latch usually has a broken or rotted frame member behind the boards. We rebuild the frame, add corner bracing where the original lacked it, and reset the hinge post if it has pulled out of plumb. Most wood gate sag correction in Angleton runs $170 to $380.
Board & Latch Replacement
We replace rotted boards with pressure-treated or cedar stock, and we swap out latches that have corroded to nothing after a few humid seasons. Figure $120 to $280 for a typical board and latch replacement. If the gate is beyond saving, we’ll tell you straight, and we’ll give you a written number on a new build before anything comes apart.
Trusted Brands We Service in Angleton
Our technicians train across nine major gate-operator brands, and around Angleton we most often see LiftMaster, FAAC, and BFT systems on the residential and ranch gates we service. We stock common control boards, limit switches, and remote receivers for these brands so we can often complete the repair on the first trip rather than ordering a part and coming back next week. That matters when your gate is stuck open and your livestock is curious about the road.
Common Gate Repair Problems We See in Angleton Homes
- Flood-submerged operators and control boards. Brazos River basin flooding soaks motors, boards, and low-mounted wiring. Repair often means replacing components and relocating them above flood stage, not just swapping the failed part.
- Clay-driven post heaving and settling. The expansive soils around Angleton swell and shrink seasonally, pushing posts out of plumb and throwing swing gates and slide gates into misalignment.
- Salt-accelerated rust on hardware. Hinges, latches, and untreated steel frames corrode faster here than in drier parts of Texas, even on properties 30 or 40 miles inland from the Gulf.
- Wind load on solid infill gates. A solid metal or wood gate catches hurricane-force wind like a sail. The load transfers to the hinges and the post, and that’s where things tear loose during a blow.
Pricing for Gate Repair in Angleton, TX
Here’s what we’re writing on estimates in Angleton right now. A hinge and realignment job runs $180 to $420. Weld and rust repair runs $160 to $400. Wood gate sag correction runs $170 to $380. A control board or receiver replacement on a LiftMaster, FAAC, or BFT operator runs $220 to $520 parts and labor. A full swing-gate actuator swap runs $450 to $900. The written estimate is free, and the number we write is the number you pay. No after-the-fact surprises, ever.
We Also Serve Cities Near Angleton
Our crews run county-wide, serving Gate Repair in Angleton plus Lake Jackson, Clute, Freeport, and Alvin. If your property sits just outside the city limits or off a county road between town and the Brazos, call us. We’ll route the nearest truck to you.
Serving Angleton, TX - Our Local Coverage Area
We’re based in the Angleton area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Angleton
Most flood-damaged gate systems around Angleton are repairable, but the repair has to include more than swapping the dead part. After Hurricane Harvey and the Brazoria County events that followed, many operators were reinstalled at the same low elevations, so we’re regularly pulling corroded control boards off gates that were “fixed” once already. We replace the board, rewire the low-mounted connections, and relocate the control box, loop detector wiring, and keypad entry station above realistic flood stage. That elevation step is the difference between a repair that lasts and a repair you’ll be calling about again after the next high-water event. Call (940) 412-7340 for an exact quote on your system.
Every automatic gate has a manual release mechanism, usually a keyed lever or pull handle on the operator itself. Pulling it disengages the motor so you can push the gate open by hand. But do this carefully. A heavy ranch gate on an acreage lot carries real momentum once it starts moving, and a solid infill gate in wind can push hard enough to hurt someone. If your operator is submerged or the gate is off its track, don’t force it. Call us and we’ll get it secured safely.
The clay-heavy soils under Angleton expand when they take on water, and that movement pushes post footings out of plumb. A gate that was square last week starts dragging the latch side after a few days of rain on the east side of town or out toward the county agriculture country. This is a footing and alignment problem, not a hinge problem, even though the hinge usually takes the blame. We reset the post below the movement zone and re-tension the gate so it rides true through the next wet season. Call (940) 412-7340 and we’ll get it squared away.
We repair both, and around Angleton we run a lot of farm and cattle gate calls. The ranch properties and acreage lots here use heavier tube steel, wider swing spans, and more utilitarian hardware than standard suburban driveway gates. The same things fail: posts in clay, rust in the coastal air, and operators that were never sized for the gate weight. We’ll put a written price on any of it before we start.
In Brazoria County, an automatic gate should have a minimum of two independent entrapment-protection devices, typically photoelectric sensors across the gate opening and a reversing edge or inherent obstruction sensor on the operator itself. Flooding and corrosion knock these out silently, which is why we test them on every call, even when the customer only called about a noisy operator. If yours isn’t working, we’ll show you and put the fix on the estimate.
Written by Dean Prescott, Owner at Portcullis Gate Repair, serving Angleton and surrounding Brazoria County communities.