Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Company in Bedford, TX
Gate work in Bedford is mostly about older hardware on shifting ground. The city was built out between the 1970s and early 1990s, which means most gates around here are 40 to 50 years old and sitting on Tarrant County clay that heaves with every wet season and contracts during droughts. That combination – aging steel hinges, treated posts well past their service life, and soil that never stops moving – is what we deal with most days. If your gate drags, won’t latch, or has dropped off its hinges, call (940) 412-7340 and we’ll give you a straight answer about what’s actually wrong.
Why Bedford Homes Are Different
Bedford is a built-out Mid-Cities bedroom community, and the housing stock tells the story. Most of the residential lots are 1970s and 1980s suburban ranch and traditional tract homes with wood privacy fences around the backyards. Many of those fences still carry their original steel hinge hardware and treated-lumber posts from the day they were built. That’s four-plus decades of North Texas freeze-thaw cycles, spring thunderstorm winds, and – the bigger issue – shrink-swell clay soil under every post. When that black clay gets wet, it expands. When it dries, it contracts. Over 40 years that cycle pushes posts out of plumb, and suddenly the gate that worked fine last fall is binding, dragging, or swinging loose on one hinge.
Our technicians working the older subdivisions in Bedford see the pattern constantly. The visible problem is usually a gate that won’t close or a latch that misses the striker. The real problem is what the soil did to the post. We tell every Bedford customer the same thing: we won’t just replace the hinge and call it done if the post underneath has moved. A hinge job on a heaving post fails again within a season, which is exactly the kind of callback that wastes everyone’s time. The Kingswell Guarantee has been built around not doing that.
Our Main Bedford Services
Most calls we get in Bedford fall into two buckets: repairs on gates that have finally given out, and replacement or new installation where a gate has gone past the point of repair. Every job starts with a written price before any work begins. Here’s what each service involves in Bedford specifically.
Gate Repair in Bedford
The majority of Bedford repair work is on wood privacy gates and steel tube gates from that original 1970s-1990s construction era. We routinely replace hinge hardware, re-hang sagging gate leaves, rebuild latch systems, and – more often than anywhere else – reset posts that have been lifted by the clay. When a Bedford customer tells us the gate drags on the ground or won’t latch, the first thing we check is whether the post has moved. See what’s covered and read through the repair process on our Gate Repair in Bedford page.
Gate Installation in Bedford
Bedford is essentially landlocked and built out, so new-construction installations are rare. What we do install is almost always replacement: a rotted wood gate swapped for a steel or aluminum frame, or a new drive gate where an old iron one has finally failed. Posts here get set with the clay in mind – deeper than the frost line and backfilled so the seasonal heave has less to grab. Pricing, material options, and how we handle the demo and haul-away are on our Gate Installation in Bedford page.
Electric Gate Repair in Bedford
Electric gate systems in Bedford run on actuators, control boards, safety loops, and keypads – and the soil is still the wildcard. When a driveway gate won’t open, sometimes it’s a dead capacitor in the control board. Sometimes the actuator is pushing against a post the clay has moved. Either way, we diagnose the whole system and give you the repair price in writing before any parts come off the gate. That full list is on our Electric Gate Repair in Bedford page.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service in Bedford
We carry service parts for the gate operators most common on Bedford properties, including Viking, Ghost Controls, DoorKing, and Elite. Stocking those parts locally lets us complete most board and actuator repairs in a single visit. If your operator’s brand isn’t on our regular list, check our brands for the full line.
Pricing for Gate Company in Bedford, TX
| Service | Typical range in Bedford |
|---|---|
| Hinge replacement (wood privacy gate) | $165-$290 |
| Latch rebuild or replacement | $120-$220 |
| Gate leaf re-hang and realignment | $185-$340 |
| Steel tube gate frame repair | $275-$520 |
| Post reset in clay soil (single post) | $220-$420 |
| Post replacement with new concrete footer | $390-$680 |
| Swing gate wheel replacement | $140-$240 |
| Driveway gate actuator swap | $640-$1,160 |
| Control board replacement | $380-$710 |
| Safety sensor or loop repair | $210-$390 |
Bedford prices do trend toward the upper half of those ranges because post work is so often part of the job. A hinge replacement on a post that has heaved out of plumb is a different job than the same hinge on solid ground. Either way, every one of those numbers is a written price agreed on before we turn the first bolt, and every repair carries a 365-day written guarantee.
Neighborhoods We Serve in Bedford
We work across the whole city, from the older subdivisions off Harwood Road to the neighborhoods east of Highway 121. The work shifts from block to block depending on the era the houses were built, which for Bedford mostly means the gates are all aging out at roughly the same time. Typical response for a non-emergency call in Bedford is same-day or next-morning.
- Woodridge
- Hickory Hills
- Parks of Bedford
- Trinity Meadows
- The Crossings at Bedford
Service Area – Cities Near Bedford
We take gate work in the neighboring Mid-Cities communities as well. If your property is in Colleyville, TX, Euless, TX, Hurst, TX, or North Richland Hills, TX, the same Kingswell Guarantee applies: written price, real arrival window, clean job site, and a written 365-day guarantee on the repair.
Serving Bedford, TX - Our Local Coverage Area
We’re based in the Bedford area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Company in Bedford
Most non-emergency calls in Bedford get a same-day or next-morning arrival window. We set the window when you call and treat it as a commitment, not a suggestion. A live person answers the phone 24/7 at (940) 412-7340.
Bedford HOAs vary. Some have architectural review for fence or gate changes, others only care about the outside facing a street. If your HOA has rules, we recommend you check them before we start. We can provide a simple written description of the work for any paperwork.
It can, especially if the posts were set in the 1970s and 1980s with shallow footings. When we reset a post, we dig a deeper footer and backfill to account for the expansion. That’s how we keep the gate from drifting again within a season. Call (940) 412-7340 for a free estimate.
For any other questions, call (940) 412-7340. A live person answers, gives you a real dollar range before you commit, and can schedule a visit that works with your day.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Bedford Customers Say
"Our driveway gate stopped halfway and wouldn't close, which is a problem when it's the only thing between the street and the yard. They came out same day, replaced the motor, and it's smooth again."
- Leonard Pace"Gate wouldn't respond to the remote or the keypad. Turned out to be the control board. They had the part and swapped it the same visit. Quoted it first, no surprises."
- Everett Shaw"Electric gate kept doing its own thing, opening at random. The tech found a shorted sensor and a worn board, fixed both, and showed me the old parts. Price was what he quoted on the phone."
- Cassandra Pike