Ghost Controls Electric Gate Repair Nationwide

Ghost Controls Electric Gate Repair in Los Angeles: What to Know First

We provide independent Ghost Controls electric gate repair in Los Angeles, typically diagnosing and fixing the issue same-day or next-day depending on parts. Most Ghost Controls jobs run $180-$650, and you’ll get that price in writing before we touch a single wire. This page is for Los Angeles homeowners whose Ghost Controls TSS1, TDS2, or premium Architectural Series gate has stopped responding to remotes, started beeping error codes, or reversed for no apparent reason. Call (940) 412-7340 and a live person will pick up, 24 hours a day.

Call (940) 412-7340

How Ghost Controls Products Fail - and How We Fix Them

• TSS1 and TDS2 single-gate kits - limit switch corrosion. The magnetic limit switches on these entry-level swing-gate operators sit exposed to Los Angeles morning marine layer and sprinkler overspray. After two or three wet seasons, the reed switch contacts oxidize and the gate “forgets” where to stop. We replace the limit switch assembly with a sealed aftermarket equivalent that holds up better near the coast, then recalibrate the open and close positions with the controller in learn mode.
• TDS2 dual-gate systems - desynchronized actuator arms. When one arm moves faster than the other, the gate leaves scuff marks on the driveway or binds at the center stop. This usually traces to mismatched capacitor values in the control boxes, or one arm running on a weak battery while the other pulls full AC. We match the capacitor specs, test both battery backup circuits under load, and resync the master/slave timing through the TDS2 control board.
• Architectural Series - control board failure after heat cycles. The AXWV or AXPC boards run hotter than Ghost Controls advertises in direct Los Angeles sun, especially on south-facing driveways in the Valley. The relay solder joints crack after repeated thermal expansion. We pull the board, inspect under magnification, and either resolder the relay legs or swap in a new board. We don’t try to band-aid a cracked trace; the next heat wave will finish it off.
• All Ghost Controls lines - battery backup that won’t hold charge. The 12V 7Ah sealed lead-acid batteries Ghost Controls ships are adequate for temperate climates. In Los Angeles, where a July afternoon can park 140°F inside a control box, those batteries sulfate and die in 18 months. We upgrade compatible systems to AGM deep-cycle batteries with higher heat tolerance, and we test the charging circuit to make sure it isn’t overvolting the new battery.
• AXWK wireless keypad - intermittent signal or total dropout. The keypad pairs on a rolling-code frequency that can clash with newer Wi-Fi extenders or smart home hubs in dense Los Angeles neighborhoods like Koreatown or West Adams. We reprogram the keypad to a clear frequency channel, check the antenna connection at the control board for corrosion, and replace the keypad if the RF module itself has failed.

Our Ghost Controls Electric Gate Repair Process

1. 1
   Call intake with a live person. We ask which Ghost Controls series you have, what it’s doing, and whether the keypad shows any error flashes. This lets our technician pull the right parts before leaving the warehouse.
2. 2
   On-site diagnostic. We test power at the outlet, voltage at the control board, and load on each actuator. For battery backup systems, we simulate a power outage and measure actual reserve time.
3. 3
   Written price before work. We itemize parts, labor, and any upgrades. Written price first, work second - that’s the only order that makes sense.
4. 4
   Repair with OEM or quality aftermarket parts. We stock Ghost Controls-compatible limit switches, control boards, and actuators. When OEM is backordered, we use aftermarket parts that match or exceed the original spec, and we tell you which we’re using.
5. 5
   Full cycle testing and safety check. We run the gate through 20 open-close cycles, test the entrapment protection, and verify the keypad and remotes from both sides of the driveway.
6. 6
   Cleanup and written guarantee. We leave the job site clean, and you get a repair invoice with the 365-Day Done Right Promise stamped on it.

What Ghost Controls Electric Gate Repair Costs in Los Angeles

What moves the price: whether we can rebuild the existing component or need a full replacement, whether the control box has heat damage beyond the failed part, and whether your gate is single or dual swing. We don’t charge extra for after-hours calls, and we don’t add trip fees inside Los Angeles County. Call (940) 412-7340 for a free estimate - we’ll give you a real number, not a range that doubles when the truck arrives.

Why Los Angeles Homeowners Call Portcullis Gate Repair for Ghost Controls Work

Dean Prescott and our technicians have worked on Ghost Controls systems since the brand first gained traction in Los Angeles around 2015. We know the difference between a TDS2 that’s lost its limit calibration and one with a failing control board, and we won’t waste your time guessing. Every repair carries the Kingswell Guarantee: written price, real arrival window, clean job site, and a 365-Day Done Right Promise on the repair. If it fails, we come back free. We’re also trained on LiftMaster, Mighty Mule, and DoorKing, so if your Ghost Controls operator isn’t worth repairing, we can quote a replacement that fits your gate without a second company’s markup.

FAQs