Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Company in Millbrae, CA
Gate work in Millbrae splits into two distinct problem sets depending on which side of El Camino Real you live on. East of the Camino, bay-facing homes deal with salt-laden air that corrodes iron hardware measurably faster than inland Peninsula cities. West of it, hillside driveways with 15 to 20 percent grades put constant strain on hinges, operators, and post footings. We handle both, and we write the price down before any work starts. Call (940) 412-7340 and you’ll get a live person, not a voicemail tree.
Why Millbrae Homes Are Different
Millbrae’s housing stock runs heavily toward post-WWII single-family homes built between the late 1940s and the 1970s. A lot of those properties still have their original ornamental wrought iron driveway and side-yard gates, which means we spend a good portion of our Millbrae calls at the welds and hinge points where rust has been working for fifty-plus years. On the eastern flats near the Bay, marine air keeps iron and steel damp through the winter fog belt, so hardware rarely fully dries out and oxidation compounds quickly.
West of El Camino Real, the terrain changes the job. Hillside lots on clay-heavy Bay Area soil shift seasonally, and gate posts heave out of plumb. A call that comes in as “gate won’t close” on a hill street is often actually a post-reset job before any hinge or latch repair can hold. That combination, corrosion work in the morning and slope work in the afternoon, is a Millbrae signature we don’t see as often in neighboring Burlingame or San Bruno.
Our Main Millbrae Services
Most Millbrae homeowners reach us for one of three reasons: a gate that stopped moving, a gate that was never there in the first place, or an electric operator that quit responding. Each has its own dedicated Millbrae page below.
Gate Repair in Millbrae
Repair calls in Millbrae tend to fall into two camps: rusted hinges and latches on older ornamental iron gates near the Bay, and sagging or misaligned gates on hillside driveways west of El Camino. We assess the hardware first, then the posts, because a gate that won’t latch on a sloped driveway often has a footing problem underneath it. Every repair gets a written price before we touch a bolt and a written guarantee when we’re done. See Gate Repair in Millbrae for full details.
Gate Installation in Millbrae
New gate installations in Millbrae need to account for grade, soil movement, and salt exposure from day one. A flat-terrain install spec rarely holds up on a hillside lot with clay soil that swells in winter. We take measurements, check the post depth and footing condition, and spec hardware that fits the actual slope and exposure. You’ll get a written quote before anything is ordered, and the Kingswell Guarantee applies to the completed installation. Full scope is on Gate Installation in Millbrae.
Electric Gate Repair in Millbrae
Automatic gate operators in Millbrae fail for predictable reasons: salt corrosion inside the control board housing on bay-side properties, and actuator strain on steep hillside driveways where the motorized arm works against gravity on every cycle. We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, so the tech who arrives already knows the system on your property. Details are on Electric Gate Repair in Millbrae.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service in Millbrae
Our Millbrae trucks carry common parts for FAAC, BFT, and Linear operators, along with Viking control boards and a range of replacement hinges, rollers, and receivers. That local stock means many repairs finish same-visit. For the full list, see our brands.
Pricing for Gate Company in Millbrae, CA
| Service | Typical range in Millbrae |
|---|---|
| Hinge and weld repair on ornamental iron gate | $180-$420 |
| Gate post reset (hillside, out-of-plumb post) | $220-$500 |
| Swing gate actuator swap (parts and labor) | $450-$900 |
| Slide gate operator replacement | $600-$1,200 |
| Control board replacement (FAAC, BFT, Linear) | $250-$600 |
| Keypad or receiver replacement | $120-$350 |
| Standard single swing gate installation | $1,800-$4,000 |
| Sloped driveway gate installation with anti-sag hardware | $2,500-$6,000 |
| Full service call and diagnosis | $75-$150 |
In Millbrae, the two big price movers are hillside grade accommodation and bay-side corrosion remediation. A post that needs resetting in clay soil, or a gate frame that needs rust abatement before new hardware can go on, adds labor hours. Whatever the scope, you get the price in writing before any work begins, and it doesn’t change at the door.
Neighborhoods We Serve in Millbrae
We cover the full width of Millbrae, from the bay-facing flats to the hillside streets west of El Camino Real.
- Mills Estates
- Millbrae Highlands
- Lomita Park
- Hillcrest
- Downtown Millbrae
Most Millbrae jobs get a technician out within a day, and we give you a real arrival window when you book. We don’t do four-hour “sometime between” windows.
Service Area – Cities Near Millbrae
Our crews serve Millbrae and the surrounding Peninsula cities, so if you’re just over the border we can likely help. We cover San Bruno, CA to the north, Burlingame, CA to the south, South San Francisco, CA up the Bay side, and Pacifica, CA over the hill. Dispatch and scheduling for Millbrae run from our San Francisco Bay Area office, but the crews are local and know the terrain.
Serving Millbrae, CA - Our Local Coverage Area
We’re based in the Millbrae area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Company in Millbrae
Most Millbrae calls get a technician dispatched the same day or the next morning. You’ll get a real arrival window when you book, and we hit it. Call (940) 412-7340 and a live person answers, 24 hours a day.
Most repairs and operator replacements on existing gates don’t require a permit. New installations with electrical runs or significant concrete work often do. We’ll tell you during the estimate whether your job needs city sign-off and what that involves.
Yes. Every repair carries the 365-Day Done Right Promise in writing on the invoice. If the repair fails inside that year, we return and fix it at no charge.
Call (940) 412-7340 for a free estimate. You’ll get the price in writing before any work starts, and the guarantee in writing when it’s done.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Millbrae Customers Say
"Gate wouldn't respond to the remote or the keypad. Turned out to be the control board. They had the part and swapped it the same visit. Quoted it first, no surprises."
- Everett Shaw"Electric gate kept doing its own thing, opening at random. The tech found a shorted sensor and a worn board, fixed both, and showed me the old parts. Price was what he quoted on the phone."
- Cassandra Pike"Installed a new gate for us after the old wooden one rotted out. Clean work, showed up on time both days, and the written price didn't change. It swings perfectly."
- Donna Kirkpatrick