Ghost Controls Hinge & Roller Replacement Nationwide

Ghost Controls Hinge & Roller Replacement: The Los Angeles Owner’s Guide

We stock and install Ghost Controls-compatible hinge and roller assemblies for most residential swing-gate systems, with typical installed pricing running $220-$380 for a standard dual-hinge set including labor in Los Angeles. Most calls we dispatch same day, and we carry the common Ghost Controls sizes on every service truck. Homeowners usually notice the problem first as a grinding scrape when the gate opens, or the gate hanging slightly crooked in its closed position - often worse after a rainy winter week when the rollers have seized and the hinge pins have started wallowing out their bushings.

Call (940) 412-7340

Which Ghost Controls Models This Applies To

Ghost Controls uses two main hinge and roller configurations across their product lines: the standard-duty series found on TSS1, TDS2, and DSS1/DSS2 kits, and the heavy-duty variant on the AXWK and premium ornamental packages. The quickest way to identify yours is the gate weight rating sticker on the operator control box - standard series handles gates up to 900 pounds, heavy-duty up to 1,500 pounds - and the physical hinge casting number stamped on the barrel, usually visible once you brush the grease away.

The standard Ghost Controls hinge uses a 5/8-inch diameter pin with a nylon bushing; the heavy-duty jumps to a 3/4-inch pin with a bronze oilite bushing and a wider 2.5-inch barrel spacing. Mixing these up is the most common ordering mistake we see in Los Angeles - a standard hinge on a heavy gate will wallow out in six months. We carry both OEM Ghost Controls hardware and a quality aftermarket equivalent from D&D Technologies that matches the pin diameter and bolt pattern exactly. For most residential setups, the aftermarket saves about $40 and carries the same 365-day guarantee from us. We’re an independent service provider, not affiliated with Ghost Controls, so we’ll tell you straight when the OEM part is worth the premium and when it isn’t.

Signs Your Ghost Controls Hinge & Roller Replacement Is Failing

• Grinding or squealing during the open/close cycle. The nylon or bronze bushing inside the hinge barrel has worn through, and metal is now rubbing on metal. In Los Angeles, this accelerates when dust from Santa Ana wind events gets past the grease seal and acts as abrasive grit.
• Gate visibly sagging or dragging at the latch end. The hinge pin has elongated the barrel bore, allowing the gate leaf to drop. On a dual-swing setup, you’ll notice the meeting stiles no longer align cleanly.
• Intermittent operator faults or “obstruction detected” errors. The Ghost Controls control board senses abnormal current draw as the motor fights the added friction. Owners often replace the operator first when it’s actually the hinge binding.
• Roller wobble or the gate “walking” sideways in the track. The roller bearings have failed, or the roller axle bolt has loosened and wallowed its mounting hole. This is more common on the heavy-duty ornamental gates we see in Hancock Park and Pasadena.
• Visible rust weeping from the hinge barrel or cracked grease fittings. Water intrusion has started internal corrosion. Once this begins in our coastal-adjacent climate - particularly west of the 405 where marine layer moisture lingers - the hinge is living on borrowed time.

Replacement Cost & What’s Included

What drives the range: gate weight and width, whether the existing bolts are seized and need extraction, and whether the post or pillar mounting surface has rotted or spalled and needs repair before new hardware will seat properly. We quote every job in writing before turning a bolt, and that written price includes the 365-Day Done Right Promise. If the repair fails inside that window, we return and correct it at no charge. Written price first, work second - that’s the only order that makes sense.

DIY or Call Us?

There’s a safe middle ground here. A homeowner can check whether the hinge grease fittings take fresh grease, whether roller bolts are loose, and whether the gate is visibly sagging - all useful diagnostic steps that help us when you call. But the actual replacement involves supporting a gate leaf that typically weighs 150-400 pounds while removing its primary pivot point. Without proper jacks, spreader bars, and a second set of hands, the gate can twist, bind, or drop. We’ve also seen DIY attempts where the operator arm was left connected during hinge removal, damaging the actuator’s internal limit switches.

If you’re comfortable with the diagnosis but not the heavy lifting, call us at (940) 412-7340. We’ll confirm the part match over the phone, quote the installed price, and usually have a technician there same day.

FAQs