Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Company in Broadview Park, FL
Gate service in Broadview Park runs into a specific set of conditions: unincorporated Broward County permitting, wind-load codes tightened since Hurricane Andrew, and a housing stock of 1950s through 1970s concrete-block ranch homes whose original gate posts are often set in footings that predate modern standards. Most calls involve corroded iron, heaved hinges, or operators that have given up in the humidity. We quote a written price before any work starts, on every job, and back the repair with our 365-Day Done Right Promise. Call (940) 412-7340 for a free estimate.
Why Broadview Park Homes Are Different
Broadview Park is an unincorporated Broward County community, so gate permits and inspections run through the county’s building department, not any city hall. That distinction matters more than most homeowners expect. Any gate replacement in Broadview Park has to meet county wind-resistance requirements, usually a product approval or an engineer’s letter, and crews who normally work under Fort Lauderdale or Davie municipal rules sometimes miss that step entirely when they cross into the community. We handle the county paperwork as part of the job.
The homes themselves add another layer. Broadview Park is built out almost entirely in modest CBS ranch homes on flat 6,000 to 8,000 square foot lots, most with low masonry or chain-link perimeter fencing and simple swing-gate driveways. The original ornamental iron and chain-link driveway gates are now decades old. Their posts sit in footings that have heaved or cracked from South Florida’s expansive marl soil and periodic sheet flooding, which throws hinge alignment out and leaves posts leaning. Add year-round humidity, intense UV, and salt-laden air drifting a few miles inland from the tidal canals, and the bottom rails and hinge plates on untreated steel corrode far faster than they would in a drier inland market. We routinely see ground-level welds rot out within 10 to 15 years without regular treatment.
Our Main Broadview Park Services
Broadview Park homeowners call us most about two things: a gate that no longer swings or slides properly, and a gate they want upgraded or replaced. We also handle the electrical side when an operator quits. Each service has its own Broadview Park page with full detail.
Gate Repair in Broadview Park
A sagging or stuck gate in Broadview Park is usually a hinge, post, or weld problem made worse by the local soil and humidity. We replace corroded hinge plates, bring leaning posts back to plumb, and patch or rebuild rusted bottom rails. On homes where the original footings are undersized, we explain what county code expects before we touch anything. Learn more here: Gate Repair in Broadview Park
Gate Installation in Broadview Park
New gate work in Broadview Park starts with the county wind-load question. If a replacement gate is going in, we confirm the product approval or engineer’s letter that Broward County requires, then build or install to that standard. Most Broadview Park yards work best with a simple swing design sized to the existing driveway and set on new posts with proper footings for the soil. Learn more here: Gate Installation in Broadview Park
Electric Gate Repair in Broadview Park
When an operator stops responding, the cause in Broadview Park is often moisture intrusion in the control board, a failed capacitor, or a sensor knocked out of alignment by a post that has shifted. We diagnose the specific system on the property, from Viking and Ghost Controls to DoorKing and Elite, and quote the repair in writing before we start. Learn more here: Electric Gate Repair in Broadview Park
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service in Broadview Park
Our technicians carry parts and service experience for the operators Broadview Park homes actually use, including Viking, Ghost Controls, DoorKing, and Elite. We also work on LiftMaster, FAAC, BFT, Linear, and Mighty Mule – see our brands page for the full list. Stocking common boards and capacitors locally means fewer return trips waiting on parts.
Pricing for Gate Company in Broadview Park, FL
These are the ranges Broadview Park homeowners typically see for common gate work, parts and labor combined. Every job gets a written price before any work begins.
| Service | Typical range in Broadview Park |
|---|---|
| Hinge replacement (repair) | $175-$425 |
| Post reset / re-plumb | $350-$800 |
| Bottom rail rust repair | $250-$650 |
| Basic swing gate install | $900-$2,400 |
| Ornamental iron gate install | $1,600-$4,200 |
| Chain-link driveway gate install | $700-$1,800 |
| Operator motor swap | $550-$1,200 |
| Control board replacement | $350-$850 |
| Safety sensor / photo eye replacement | $180-$400 |
| Full operator + gate package | $2,800-$7,500 |
Broadview Park pricing runs higher than drier inland markets when the existing footings fail county wind-load review and need to be rebuilt to spec. Rusted-through bottom rails also push costs up when the damage extends past the hinge plate into the main frame. Either way, the price you approve is the price you pay; there is no after-the-fact correction.
Neighborhoods We Serve in Broadview Park
We cover all of Broadview Park, from the older ranch-home streets near State Road 7 to the residential blocks running east toward the canals. Our crews respond across the community, usually within one business day for repair calls.
- The original 1950s ranch blocks near SR 7
- Residential streets east toward the tidal canals
- Sections bordering unincorporated Broward County pockets
- Homes along the South Fork of the New River
- The commercial and residential mix near Peters Road
Service Area – Cities Near Broadview Park
While this page covers Broadview Park specifically, we also serve nearby Florida markets through our other locations: Miami, FL, Jacksonville, FL, Tampa, FL, and Orlando, FL. Scheduling for Broadview Park is coordinated from our Miami (South FL) office, with local crews dispatched to the community.
Serving Broadview Park, FL - Our Local Coverage Area
We’re based in the Broadview Park area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Company in Broadview Park
Broadview Park is unincorporated, so gate permits and inspections run through Broward County’s building department, not any city hall. Replacement gates must meet county wind-resistance standards, typically a product approval or an engineer’s letter. We handle the paperwork on permitted jobs. Call (940) 412-7340 and we will tell you what applies to your property.
Most repair calls in Broadview Park get a next-business-day visit, and we answer the phone live around the clock for emergency situations. When you call (940) 412-7340, a person picks up and gives you a real arrival window, not a callback queue.
We serve the entire community, from the original ranch blocks near SR 7 to the streets running east toward the canals. Whether your gate is iron, chain-link, manual, or automated, call (940) 412-7340 for a free estimate and a written price before any work starts.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Broadview Park Customers Say
"Gate was dragging and screeching across the driveway. I figured I'd need a whole new setup. He adjusted the track and rollers and it was a fraction of what I expected. Honest work."
- Omar Haddad"Our intercom and gate motor both quit. They fixed the whole system in one visit and explained the warranty clearly. On time, polite, and tidy. Can't ask for more."
- Yvette Marchetti"Good repair on a sagging gate and a new hinge welded on. Took them a couple days to get the part in, but they told me that up front and it's been solid since."
- Hector Villanueva