Ghost Controls Gate Repair in Fort Worth, TX

Ghost Controls Gate Repair in Fort Worth, CA | Portcullis Gate Repair

Most Ghost Controls gate repairs in Fort Worth run between $180 and $550 depending on whether you’re looking at a board swap, a full operator replacement, or a post-and-alignment fix. We’re an independent service company, not a Ghost Controls dealer, and we’ve been working on their solar and low-voltage operators across Tarrant County since they became the standard for ranch and residential installs here. Our techs carry genuine Ghost Controls boards, arms, and harnesses on the truck, and we’ll give you a written price before we touch a single bolt. Call us at (940) 412-7340 for a free estimate.

Call (940) 412-7340

Why Fort Worth Residents Choose Us for Ghost Controls Service

Dean Prescott grew up in the San Fernando Valley and learned electrical systems at Los Angeles Trade-Technical College before moving into gate work full-time. His father was a finish welder, and the mix of metal, motors, and troubleshooting felt familiar from day one. That background matters when we’re diagnosing a Ghost Controls operator that’s short-cycling or a solar battery box that’s gone dark.

We service nine major gate-operator brands, but Ghost Controls sales & service has earned special attention in Fort Worth because of how well their solar kits and low-voltage units fit ranch properties and residential acreage. The TSS1 single swing and TDS2 dual swing lines are everywhere from Fairmount historic district retrofits to pipe-frame gates off Weatherford Road. Our technicians are background-checked, uniformed, and trained specifically on Ghost Controls limit logic, proprietary harness connectors, and solar charging diagnostics. We stock genuine replacement boards and arms locally because the OEM connectors don’t mate cleanly with generic substitutes, though we’ll use quality aftermarket batteries and keypads where they outperform factory parts.

Every repair carries our 365-Day Done Right Promise in writing. If it fails, we come back and fix it at no charge. Written price first, work second - that’s the only order that makes sense.

Common Ghost Controls Gate Repair Problems We Solve in Fort Worth

• Control board and limit-switch failure after summer heat. The potted boards on TSS and TDS units sit in metal housings that bake when Fort Worth hits 105°F for weeks straight. The board stops recognizing its limit switches, so the gate reverses mid-travel or stops short. We replace with genuine Ghost Controls boards and re-learn the limits on-site.
• Corroded battery harnesses from clay soil moisture. The Blackland Prairie Vertisol clay holds water against terminals and ground-level boxes longer than sandy soils would. Solar units stop charging silently - the gate runs on battery alone until it’s drained. We clean or replace harnesses and relocate boxes above grade where possible.
• Nylon roller and hinge wear from heat and dust. Summer dust and UV degradation crack nylon rollers and elongate hinge pins on ornamental gates in Ryan Place and Berkeley Place. The gate sags, the operator arm strains, and eventually the bracket bolts strip. We replace with brass or steel hardware rated for the load.
• Post heave from expansive clay cycles. A 36-inch post in Fort Worth’s Vertisol soil can shift two inches out of plumb within two or three wet-dry cycles. The Ghost Controls operator over-travels, the limits drift, and the gate starts binding. We probe footing depth before touching hardware; anything less guarantees a callback.
• Arm bracket fatigue on heavy pipe-frame gates. Western Tarrant County ranch gates are heavier than typical residential units. The TDS2XP arms on long pipe-frame swings develop bracket cracks or bolt elongation over time. We upgrade mounting hardware and check gate balance before reinstalling the operator.

Ghost Controls Service in Fort Worth: What Local Conditions Mean for Your Equipment

Fort Worth’s expansive Blackland Prairie clay shrinks and swells enough that a 36-inch post can heave visibly within two or three wet-dry cycles, so our Ghost Controls alignments always start with probing the footing - a step that out-of-town crews skip and then get a callback. This is far more aggressive here than in the sandier soils of Dallas or Ghost Controls in Arlington, and it’s the number-one reason a Ghost Controls operator that tests fine still fails in the field.

We were called to a pipe-frame double swing gate on a horse property off Weatherford Road running a pair of Ghost Controls TDS2XP operators that had started short-cycling and reversing at random. Our tech found the control board limped from heat and a corroded battery harness, plus the north post had heaved nearly two inches out of plumb from the clay - we re-set the post on a deeper footing, replaced the board and harness, and re-learned the limits, and the gate ran clean. The owner told us two previous companies had swapped batteries and walked away.

That story repeats across Fort Worth. The February 2021 ice event seized hydraulic operators and cracked plastic gear housings by the hundred. Summers warp metal frames and degrade rubber seals while the clay does its slow work below grade. A Gate Repair in Fort Worth for Ghost Controls here isn’t just about the operator - it’s about whether the gate and its footing can hold calibration through a full weather cycle.

Ghost Controls Models & Products We Service in Fort Worth

We work on the full Ghost Controls residential and light-commercial line: the TSS1 and TSS1XP single swing operators, the TDS2 and TDS2XP dual swing units, solar kits and battery boxes including the ABBT and SPK configurations, and the full accessory range - AXDP keypads, AXRE remotes, AXWK wireless kits, and safety edges. Our Fort Worth warehouse stocks genuine Ghost Controls control boards, operator arms, and harness assemblies because the proprietary connectors and limit-switch logic don’t tolerate aftermarket substitutes well. For batteries, keypads, and safety edges, we source quality third-party components that meet or exceed OEM spec.

If your TSS1 or TDS2 board is fried and the arm shows wear, we’ll tell you straight whether a board swap makes sense or whether you’re better off replacing the operator head. No deposit required for that conversation.

Ghost Controls Service Pricing in Fort Worth

FAQs - Ghost Controls Gate Repair in Fort Worth

Service Areas Near Fort Worth

We run Fort Worth service area calls daily and regularly reach into surrounding communities. Our Ghost Controls work extends to Ghost Controls service in Jacksonville and Ghost Controls service in Austin through our Kingswell network, with the same written pricing and 365-Day Done Right Promise at every location.

Book Your Ghost Controls Service in Fort Worth Today

A Ghost Controls gate that won’t close or keeps reversing isn’t going to fix itself, and every day it sits open is a day your property isn’t secured. We answer calls live 24 hours a day, and we offer same-day service for urgent failures - a gate stuck open, a safety sensor fault, or an operator that won’t respond to remote or keypad. Call (940) 412-7340 for a free estimate. We’ll give you a written price before any work starts, and we back every repair with our 365-Day Done Right Promise.

Written by Dean Prescott, Owner at Portcullis Gate Repair, serving Fort Worth since 2008.