Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Fort Worth
Gate installation in Fort Worth runs about $900 to $4,800 for a standard residential driveway gate, and most homeowners we work with fall between $1,500 and $3,200 for a complete install with an automatic opener. That range covers everything from a single swing gate on a Ryan Place cottage to a sliding ranch gate out west of Weatherford Road. We’re Gate Installation specialists who work throughout Fort Worth, and our crews know this city’s clay soil, historic gates, and HOA requirements better than an out-of-town shop ever could. Call (940) 412-7340 for a free estimate. We’ll give you the written price before any work starts.
Why Portcullis Gate Repair Is Fort Worth’s Preferred Gate Installation Company
We’ve built our reputation in Fort Worth by showing up when we say we will and putting the price in writing first. Not after the old gate is already on the ground. Dean Prescott leads our Fort Worth crews, and he’s the one who set the standard we still follow: probe the post depth before quoting an alignment fix, because this city’s clay will heave a shallow footing out of plumb within two or three wet-dry cycles. That’s not something a generic gate company learns from a manual. It’s something you learn from fixing hundreds of gates in Fairmount, Berkeley Place, and the Alliance corridor.
Every job carries the Kingswell Guarantee: a written price before any work begins, a real arrival window, a clean job site, and a written guarantee on the repair. If the installation isn’t done right, we come back and make it right at no charge under the 365-Day Done Right Promise. You also get a live person who answers the phone 24/7. No voicemail trees. When a Fort Worth homeowner calls about a gate that won’t open, they talk to a person, not a recording.
Driveway Gate Installation in Fort Worth
Driveway Gate Installation in Fort Worth usually means either replacing a rusted or sagging manual gate with a new automatic one, or retrofitting an opener onto an existing gate that’s still structurally sound. The job starts with measuring the driveway opening, checking the post depth and plumb, and confirming what kind of operator your HOA or historic district will allow. In neighborhoods like Fairmount or Berkeley Place, the gate style often has to match the home’s original wrought iron. In HOA-governed communities along the Alliance corridor, you may need a specific ornamental aluminum or steel design approved by the board. A complete single-swing driveway gate with opener typically runs $1,800 to $3,800 installed in Fort Worth. A double swing gate runs $2,500 to $4,800.
Automatic Swing Gate Openers on Existing Gates
If your existing swing gate is solid but you’re tired of getting out of the truck to open it, we can often add an automatic opener without replacing the gate. The operator needs a solid post to mount to, and that’s where Fort Worth’s clay complicates things. We check for post movement before quoting. A swing gate opener install with safety photocells and a keypad runs about $1,200 to $2,400 depending on the operator brand and gate weight.
Full Driveway Gate Replacement
When the gate frame itself is warped, the hinges are pulling out of rusted steel, or the gate was never hung square in the first place, replacement is usually cheaper than repeated repairs. A new ornamental steel driveway gate in Fort Worth runs $2,000 to $4,800 installed, including the operator and safety edges. We quote that price in writing before removing anything.
Sliding Gate Installation in Fort Worth
Sliding Gate Installation in Fort Worth is most common on wider driveways where a swing gate would need too much room to open, or on ranch properties with long runs along fence lines. A sliding gate rides on a track or cantilever system instead of swinging on hinges, which means it handles heavy gates better and works well on sloped driveways. In western Tarrant County, we install a lot of tube-steel sliding gates on acreage properties where the driveway is 20 feet wide or more. A standard residential sliding gate install in Fort Worth runs $2,200 to $4,600 including the operator, track, and safety sensors. Commercial-width sliding gates run higher, and we quote those case by case.
Cantilever Sliding Gates for Clay Soil
Fort Worth’s Blackland Prairie clay moves, and a track-mounted sliding gate sitting on that soil will bind and drag when the ground heaves. That’s why we frequently recommend a cantilever system for Fort Worth home sites: the gate rides on posts set deep in concrete, suspended above the ground so soil movement doesn’t jam the gate. A cantilever sliding gate install typically runs $3,000 to $5,500 in Fort Worth, and on clay soil it’s usually the right long-term answer.
Retrofitting a Manual Sliding Gate
If you already have a sliding gate but it’s never been automated, we can add a Viking or DoorKing operator and the required safety edges. The first question is whether the posts are deep enough. On a Fort Worth property with shallow posts, we may need to reset them before adding the opener. Operator-only retrofits run about $1,400 to $2,600.
Trusted Brands We Service in Fort Worth
Our technicians carry parts for Viking, Ghost Controls, and DoorKing operators on Fort Worth service calls, which means fewer return trips and faster installs. We work on LiftMaster, FAAC, BFT, Linear, Elite, and Mighty Mule systems as well. When a Fort Worth customer has a Ghost Controls opener that died after a February ice event, we usually have the control board or gear kit on the truck. That’s the kind of local parts stock that saves you a week of waiting. We also know which operators hold up best in Fort Worth’s heat: nylon rollers and rubber seals degrade fast here, so we recommend operators with metal drivetrain components where practical.
Common Gate Installation Problems We See in Fort Worth Homes
- Sagging gate despite tightened hinges. In Fort Worth, hinge tightening rarely fixes a sag because the problem is usually the post, not the hinge. The Blackland Prairie clay heaves shallow footings out of plumb, and a 36-inch-deep post can move two inches in a couple of wet-dry cycles.
- Sun-warped steel frames on older gates. Fort Worth summers over 105°F warp tube-steel and wrought-iron gate frames, throwing slide gate alignment off and wearing down nylon rollers faster than in cooler markets. We see this constantly on 1980s and 1990s ranch gates.
- Seized hydraulic operators after ice events. February 2021 was a wake-up call for a lot of Fort Worth homeowners. Hydraulic operators froze and cracked plastic gear housings on legacy control boards across hundreds of gates in a single week. A replacement with a modern electromechanical operator usually fixes it for good.
- Legacy control boards with no safety photocells. Many pre-2000 gates around Fort Worth were installed before safety photocells and reverse edges became standard. These gates can crush or trap. If you have an older automatic gate without working photocells, we recommend retrofitting safety equipment. That’s not a suggestion, it’s a safety issue.
Pricing for Gate Installation in Fort Worth, TX
Most residential gate installs in Fort Worth fall between $1,500 and $3,800, depending on the gate type, width, operator brand, and whether we’re working with existing posts or pouring new ones. Single swing gates run lower; double swing gates and sliding gates run higher. A full replacement on a wide ranch driveway can reach $5,500. What moves the price most in Fort Worth is post work. If we have to pull old shallow footings and pour deeper concrete piers, that adds $400 to $1,200 depending on how many posts. We give you that number in writing before any work starts, and the price we quote is the price you pay. Call (940) 412-7340 for a free estimate on your specific gate.
We Also Serve Cities Near Fort Worth
You’ll find our crews in Fort Worth and in the surrounding communities, including Haltom City, North Richland Hills, Hurst, and Kennedale. If your gate is sagging in Haltom City or your opener won’t respond in Hurst, the same 365-Day Done Right Promise applies. Call (940) 412-7340 and a live person will answer, day or night. That’s the Kingswell Way, and every independently owned Kingswell location is held to it.
Serving Fort Worth, TX - Our Local Coverage Area
We’re based in the Fort Worth area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Installation in Fort Worth
The sag is almost certainly in the post, not the hinge. Fort Worth sits on Blackland Prairie Vertisol clay that shrinks in drought and expands after rain. A gate post set only 36 inches deep can move two inches out of plumb over two or three wet-dry cycles. Tightening hinges doesn’t address that movement. We probe the post depth first, and when the footing is shallow, we pull the old concrete and pour a deeper pier before re-hanging the gate. If you skip that step, the gate will sag again within a year. Call (940) 412-7340 if your gate keeps dropping, and we’ll tell you what’s actually moving.
Usually, yes, we can retrofit an opener onto an existing swing gate if the posts are solid and the gate itself isn’t warped. We check both before quoting. On a Ryan Place property with an early-1900s wrought-iron driveway gate, we found the sag originated at the hinge post, not the panel. The post had heaved nearly two inches out of plumb from clay movement. We pulled the old footing, poured a deeper concrete pier, re-hung the gate with new hinges, and added a LiftMaster operator with working safety photocells so the homeowner could use keypad entry without fighting the gate. If your gate frame is straight and your posts are deep, a retrofit usually makes sense. Operator-only installs run about $1,200 to $2,400 in Fort Worth. Replacing the whole gate runs higher.
A new automatic gate in Fort Worth must include safety photocells that stop and reverse the gate when something crosses the path, and a reverse edge or other entrapment protection. These are life-safety requirements, not add-ons. We won’t install an automatic gate without working photocells and a properly adjusted reverse function. If you have an older gate without these, we recommend retrofitting them. A gate that can crush a child or a dog is not a convenience, it’s a hazard. We handle the full safety package as part of every automatic gate installation.
It usually is. Summer heat over 105°F warps tube-steel gate frames and degrades the rubber seals and nylon rollers inside operators, which can bind the gate or strip the drive gears. On ranch properties out toward Weatherford Road, we also see hydraulic operators that overheat and refuse to cycle in the afternoon. We check the frame alignment, replace worn rollers and seals, and if the operator is beyond saving, we swap it for an electromechanical unit that tolerates heat better. A new operator on a ranch gate in Fort Worth typically runs $1,400 to $3,000 depending on gate weight. Our techs carry Viking, Ghost Controls, and DoorKing parts on the truck, so most heat-failure calls get fixed same day.
Deeper than the standard suburban spec. In Fort Worth’s expansive Blackland Prairie clay, we recommend gate posts set at least 42 to 48 inches deep in concrete, not the 36 inches you’ll see in sandier soil markets. The clay heaves shallow posts out of plumb within two or three wet-dry cycles, and re-hanging a gate on the original footing just guarantees another sag. We probe post depth before quoting any alignment or installation job, and if the footing is shallow, we’ll recommend resetting it. It costs more up front, but it’s the only way a gate stays square in this soil. Call (940) 412-7340 for a free assessment, and we’ll tell you honestly what your posts need.
Call (940) 412-7340 for a free estimate on gate installation in Fort Worth. We’ll put the price in writing before any work starts, and we’ll show up in the window we gave you. That’s the Kingswell Guarantee, and it’s written on every invoice.
Written by Dean Prescott, Owner at Portcullis Gate Repair, a Kingswell company serving Fort Worth and western Tarrant County.