Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across Keller
A gate that won’t open, sags on its hinges, or groans when the operator kicks in is more than a nuisance in Keller. It’s a daily fight with a 400-pound piece of steel. Most gate repair calls we run in Keller are alignment and post problems caused by the Blackland Prairie clay shifting under the footings, not the motor itself. We send a uniformed, background-checked tech to your property with the parts to handle most repairs in a single visit. Call (940) 412-7340 and you’ll get a live person, a real arrival window, and a written price before any work starts.
Why Portcullis Gate Repair Is Keller’s Preferred Gate Repair Company
Keller homeowners have a particular set of expectations, and honestly, they should. The driveways out here hold custom ironwork that cost real money, and a gate company that treats a 16-foot ornamental swing gate like a chain-link fence job won’t last long. We’ve been at this since 2008 as a Kingswell company, and the repair calls we run in Keller follow a pattern: post footings heaved by clay, hinges pulling out of square, operators that were undersized the day they were installed. Knowing the difference between a mechanical failure and a structural one is what keeps Keller customers calling us back.
Every Portcullis location is independently owned and operated, but the Kingswell Guarantee is identical across all of them. Written price before work begins. Real arrival window. Clean job site. Written guarantee on the repair. If the repair fails inside 365 days, we come back and fix it at no charge under the 365-Day Done Right Promise. That’s not a sales pitch. It’s stamped on the invoice. Dean Prescott, who leads our team, insists on it for every single job.
Wrought Iron Gate Repair in Keller
Wrought iron gate repair in Keller usually means one of three things: a sagging leaf that drags on the driveway, a hinge or post that’s pulled out of plumb, or rust that’s compromised the pickets and welds. The ironwork on Keller’s executive lots was often custom-fabricated, and the weight of it punishes any footing that’s settled even half an inch. We pull the panel, re-plumb the post, re-pour the footing when it’s shot, and correct the sag so the leaf hangs true again. A straightening and hinge re-pour on a typical ornamental swing gate in Keller runs $450 to $950. Weld repair on cracked scrollwork or a rusted bottom rail adds $150 to $400 depending on how much section needs rebuilding.
Hinge and Post Rebuilds
When a Keller gate post heaves out of the ground, tightening the hinge bolts does nothing except strip the threads. The fix is at the footing. We dig out the old concrete, set the post plumb, and pour a new footing sized for the gate’s weight. On a standard ornamental iron single-leaf swing, a hinge post re-pour and re-hang runs $500 to $1,100 in Keller, and the gate swings better than it did the day after the original install.
Weld and Rust Repair
Bottom rails rust first. That’s where standing water sits after rain, and on Keller’s ornamental gates the bottom rail is usually the first thing to let go. We cut out the failed section, weld in matching steel, and grind it flush so the repair doesn’t look like a patch. Powder coating or spot painting after weld work keeps it from coming back for another decade.
Metal Gate Repair in Keller
Metal gate repair in Keller covers the full range of steel and tubular aluminum driveway gates, from light pedestrian wickets to heavy double-leaf slide gates on the western acreage tracts. The difference between metal gate repair and wrought iron work is mostly material thickness and weight handling. Tubular steel gates are lighter but rust at the frame joints. Solid steel slide gates are heavy enough that a marginal operator will burn out early. A typical metal gate repair in Keller, realignment plus new rollers or a hinge rebuild, runs $300 to $800.
Gate Realignment and Track Work
Slide gates on Keller properties fail when the V-track settles or the rollers wear flat on one side, which drags the leaf out of line and loads the motor until it trips. We level the track, replace the rollers, and set the end stops so the gate doesn’t slam the post every cycle. Full slide gate roller set replacement in Keller runs $250 to $600 including labor.
Gate Openers and Operator Repair
When the opener is the problem and not the gate itself, we diagnose the full loop detector, limit switches, and capacitor bank before quoting anything. Older LiftMaster, Viking, and Ghost Controls operators are common on Keller homes, and a bad capacitor or frozen limit switch is often mistaken for a dead motor. Repairing the operator board or replacing a swing-arm actuator in Keller typically runs $350 to $850.
One thing worth being clear about: the gate and the opener are separate systems, and a sagging gate will destroy a perfectly good operator. We fix both, and the written quote shows you the split between structural work and mechanical work before a single bolt is turned.
Trusted Brands We Service in Keller
Our techs carry service experience on the brands Keller homeowners actually have. We work on FAAC hydraulic arms and BFT slide operators regularly, plus Linear and Viking systems on the older builds. On the newer tucked-away acreage properties where the installer undersized the original unit, we often pull out a worn Ghost Controls or Mighty Mule and quote a properly sized replacement. Because Keller work comes in predictable patterns, our trucks carry common FAAC and Viking seals, capacitors, and limit switches so we don’t burn a return trip waiting on a distributor box.
Common Gate Repair Problems We See in Keller Homes
- Clay-soil post heave. The Blackland Prairie gumbo expands in wet springs and shrinks in summer drought, ticking gate posts out of plumb year after year. The gate racks out of square and starts binding on the hinges or track, and tightening bolts won’t touch the actual problem.
- Undersized operators on dual gates. Western Keller acreage tracts often run a pedestrian iron gate and a heavy farm-style slide gate off one opener that was never rated for the combined duty cycle. The motor burns out every two to three summers like clockwork.
- Ice storm damage to boards and seals. The February 2021 freeze cracked circuit boards and hydraulic arm seals on hundreds of Keller operators. Boards and seals don’t like hard freezes, and the symptom is a gate that worked fine in December and won’t respond by February.
- Roller and track wear on slide gates. Keller’s heavy slide gates eat rollers on the regular, especially where the track sits on a slight grade. A flat-spotted roller drags, the motor overheats, and the homeowner thinks the opener failed when it’s actually a $40 roller set.
Pricing for Gate Repair in Keller, TX
Here are straight dollar ranges for the repair work we do most in Keller, parts and labor included:
- Hinge rebuild or single post re-pour: $500 to $1,100
- Gate realignment and sag correction: $300 to $800
- Slide gate roller and track replacement: $250 to $600
- Swing-arm actuator swap on FAAC or Viking systems: $450 to $900
- Operator board or limit switch repair: $350 to $850
- Weld repair on rusted or cracked iron sections: $150 to $400
These aren’t countywide averages. They’re what we see on Keller driveways where the gates are heavy, custom, and often 15 to 25 years old. The exact number depends on gate weight, access, and whether the operator survived the misalignment. You’ll get a written quote before we start, and that’s the price. If anything changes mid-job, you approve it in writing first. Call (940) 412-7340 for a free estimate.
We Also Serve Cities Near Keller
Our crews run Gate Repair work throughout Keller and into the surrounding communities. If you’re in Haslet, North Richland Hills, Roanoke, or Southlake, same team, same Kingswell Guarantee on every job. Dispatch and scheduling are coordinated from the brand’s Dallas-Fort Worth office, and the tech who shows up lives and works this side of the metro.
Serving Keller, TX - Our Local Coverage Area
We’re based in the Keller area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Keller
Because the hinge post is moving in the ground, not the hinge bolts. Keller’s clay soil swells and shrinks with the seasons, and the post footing tilts a fraction each year. Tightening the bolts just clamps the gate to a post that’s out of plumb. The fix is re-setting the post and re-pouring the footing. Call (940) 412-7340 and we’ll tell you if your gate just needs a sag correction or a full post re-pour, with the price up front.
It’s common enough that we expect it. The wet spring swell pushes post footings up unevenly, and a heavy ornamental leaf tilted a degree out of square will bind on the latch side. It’s not normal in the sense of acceptable, but it is predictable on Blackland clay. We fix the footing, not just the gate, so it doesn’t rack again next spring. Get a written quote from our team by calling (940) 412-7340.
Most likely the original installer sized the operator for one gate, not both. In Keller’s western acreage tracts we see this all the time: a single swing opener running a decorative iron walk gate and a heavy tube-steel slide gate with a horse trailer behind it. The motor runs hot every cycle and burns out in two or three summers. The fix is a properly rated operator and often a separate actuator for each leaf. Call (940) 412-7340 and we’ll spec it correctly.
Look at the keypad and the operator first, but don’t start replacing boards. Keller ice storms freeze-crack capacitors, control boards, and hydraulic seals on older LiftMaster and Viking units, and the symptom looks just like a dead motor. A trained tech can bench-test the board and tell you if it’s a $200 capacitor or a $700 board. We’ll also check the physical gate for ice heave before condemning any electrical part. Call (940) 412-7340.
Usually not. A binding gate on a Keller property is almost always a post or track alignment issue, not a failed gate leaf. We pull the leaf, re-set the post or level the track, rehang the gate, and it typically runs like new on the original hinges. We won’t sell you a replacement gate if a re-pour fixes it. To get an honest read on yours, call (940) 412-7340 and we’ll send someone out to look.
Why Keller Gates Fail the Way They Do
Keller’s heavy concentration of privately gated executive lots on Blackland Prairie clay means most repair calls are post-footing and alignment failures, not operator motor failures. That ratio flips in neighboring cities with shared community gates and slab-track installations. Around here, the ornamental iron gate was built heavy and custom, set on a concrete footing poured into expansive clay, and left for twenty years. The clay heaves, the post tilts, the gate racks out of square, and the operator burns out trying to move a gate that no longer fits its own hinges. That’s the real story of gate repair in Keller.
In the Taylor Glen and Highland Oaks pockets off Keller-Smithfield, our tech diagnosed a 16-foot ornamental iron swing gate that had racked out of square after the wet spring. The loop detector was fine, the LiftMaster operator was fine. But the hinge post footing had heaved, so we pulled the post, re-poured the footing, re-plumbed the gate, and dialed in sag correction until it swung silently on the original hinges, saving the homeowner a full gate replacement. That homeowner was quoted $4,000 for a new gate by another company. We fixed it for under $1,100.
The Kingswell Way is the same five commitments on every Keller job: say the price before the work, show up in the window we gave, leave the place cleaner than we found it, put the guarantee in writing, and come back if it fails. Our team is led by Dean Prescott, and every repair carries the 365-Day Done Right Promise. That means if the repair fails inside a year, we return and fix it at no charge. Not “we’ll take a look.” We fix it.
Call (940) 412-7340. A live person answers, day or night, and you’ll have a written price before a single bolt is turned.
Written by Dean Prescott, Owner at Portcullis Gate Repair.